Equipped To Survive Equipped To Survive® Presents
The Survival Forum
Where do you want to go on ETS?

Page 2 of 2 < 1 2
Topic Options
#60745 - 02/22/06 07:27 AM Re: Cleaning knife gunk
ghostbear Offline
Stranger

Registered: 12/18/05
Posts: 15
Loc: Burbank, CA. U.S.A.
On my big SAK, a SwissChamp, I open all the blades and tools and put it in the dishwasher. I try to position it so that it's in directly in the path of a waterjet. After the wash, when it's dry, I lube the pivots with oil.

For adhesive gunk stuck on blades, I use these products--one at a time, in escalating order: Purell hand sanitizer, nail polish remover, Ronsonol, and freon. Fortunately, the hand sanitizer works well enough most of the time and I don't have to go any further than that. I just have to wipe vigorously.

Top
#60746 - 02/22/06 02:45 PM Re: Cleaning knife gunk
Anonymous
Unregistered


I've been cleaning antique scientific instruments and other mechanical devices for about 30 years. Maybe I can lend some advice here.

Disassemble whatever can be easily removed. Yes, start with compressed air and force the loose dry material (usually lint) out of the workings of the knife (I would use a compressor if you have one). Avoid cotton swabs to clean; cotton may get stuck in the works. Use toothpicks, tooth brushes, dental tools other blades etc. Brass bristle brushes are the best for breaking up gunk.... I use brass brush tips that are typically used with Dremels but attach them to a handle for cleaning by hand. Keep cleaning the knife without solvents until you get as much gunk/lint out as possible.

Next, for that stubborn materials, use any solvent that quickly evaporates, or, use a solvent that when chased with alcohol or acetone, will mix with it and promote drying. I use an assortment of cleaning solvents, the more common ones include: lacquer thinner, acetone, alcohol, ammonia, thinners, and any fuels, including lighter fluid, gasoline, charcoal starter, to name a few. You do not want to leave any moisture in the pivots between bolsters and handle or any other place where it can sit and begin an oxidation problem.

After you have loosened and removed the dirt, rinse with alcohol or acetone and blow out the moisture with compressed air again. If you suspect moisture is stuck in certain areas, again rinse the area with acetone or alcohol and blow it dry. I would NEVER recommend using a dishwasher or soap and water to clean a knife unless it was totally disassembled. Water hides in places where it can promote oxidation and even the heat from a dishwasher cannot evaporate hidden moisture.

Only after the knife is totally cleaned and dried should it be sparingly lubed. After the hinges are saturated, (Prolix, teflon, light machine oil....your choice), once again blow out all the excess so the remaining lubricant will not work like a lint magnet in your pocket. Avoid silicone based lubes....silicone can hide water. The more excess lube you can remove the better. Think of the excess lube as the material you'll be trying to scrub out during your next cleaning session.


Top
#60747 - 02/22/06 02:51 PM Re: Cleaning knife gunk
paramedicpete Offline
Pooh-Bah

Registered: 04/09/02
Posts: 1920
Loc: Frederick, Maryland
Just be careful when using various solvents with plastic handled/scaled knives such as SAKs, the handles/scales can start to melt and the adhesive, which holds the handles/scales, can dissolve. I speak from experience <img src="/images/graemlins/blush.gif" alt="" />.

Pete

Top
#60748 - 02/24/06 01:11 AM Re: Cleaning knife gunk
Steve Offline
Journeyman

Registered: 05/29/04
Posts: 84
Loc: North Carolina
If you do use water, be careful how hot it is. I had the great idea to dunk my SAK in boiling water and warped the liners. A lesson in differential thermal expansion <img src="/images/graemlins/blush.gif" alt="" /> Plus it lightened the color of the scales.

Steve
_________________________
"After I had solaced my mind with the comfortable part of my condition, I
began to look round me, to see what kind of place I was in, and what was
next to be done"

Top
#60749 - 02/24/06 03:08 AM Re: Cleaning knife gunk
KenK Offline
"Be Prepared"
Pooh-Bah

Registered: 06/26/04
Posts: 2208
Loc: NE Wisconsin
Someplace I heard somebody say to toss the knife into the dishwasher, but I worry that the dishwasher detergent is just too harsh.

Top
#60750 - 02/24/06 03:22 AM Re: Cleaning knife gunk
Anonymous
Unregistered


Do Not Use Water.... Do Not Use Soaps....Do Not Use A Dishwasher.
Read this.......

..And yes, as previously mentioned by ParamedicPete, be careful of the effects of solvents on plastics and glues.

Top
#60751 - 02/24/06 05:10 AM Re: Cleaning knife gunk
lukus Offline
Member

Registered: 02/03/06
Posts: 170
Loc: TEXAS (where else?)
Heat+moisture=oxidation (think dishwasher)

Nail polish remover is just pretty acetone, not something I would use on most folders. It will melt a lot of plastics and take enamel off (i.e. nail polish/paint), it will even take off some protective coatings like parkerizing. Ronsonol and mineral spirits are a lot safer for removing adhesives.

Top
Page 2 of 2 < 1 2



Moderator:  Alan_Romania, Blast, cliff, Hikin_Jim 
March
Su M Tu W Th F Sa
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Who's Online
0 registered (), 444 Guests and 28 Spiders online.
Key: Admin, Global Mod, Mod
Newest Members
GallenR, Jeebo, NicholasMarshall, Yadav, BenFoakes
5367 Registered Users
Newest Posts
What did you do today to prepare?
by dougwalkabout
03/27/24 11:21 PM
Zippo Butane Inserts
by dougwalkabout
03/27/24 11:11 PM
Question about a "Backyard Mutitool"
by Ren
03/17/24 01:00 AM
Problem in my WhatsApp configuration
by Chisel
03/09/24 01:55 PM
New Madrid Seismic Zone
by Jeanette_Isabelle
03/04/24 02:44 PM
EDC Reduction
by EchoingLaugh
03/02/24 04:12 PM
Newest Images
Tiny knife / wrench
Handmade knives
2"x2" Glass Signal Mirror, Retroreflective Mesh
Trade School Tool Kit
My Pocket Kit
Glossary
Test

WARNING & DISCLAIMER: SELECT AND USE OUTDOORS AND SURVIVAL EQUIPMENT, SUPPLIES AND TECHNIQUES AT YOUR OWN RISK. Information posted on this forum is not reviewed for accuracy and may not be reliable, use at your own risk. Please review the full WARNING & DISCLAIMER about information on this site.